Products

Description The trapezoidal sheet metal mounting base is ideal for watertight installation on the raised beads of trapezoidal sheet metal roofs. A solar module is installed directly on the trapezoidal sheet metal bridge. Optionally, adapter feet can be inserted into the rail and an additional inclination of 5 or 7 degrees is achieved. By clamping on the long side of the module frame, the module maintains the best possible load capacity. Thanks to thread-cutting screws, fastening takes place without pre-drilling. Screws and already glued EPDM seal prevent moisture from penetrating. The modules can be attached horizontally or vertically directly to the mounting rails or adapter feet using module clamps. scope of delivery 1 adapter at the front for mounting the front side of the module Complementary products: Mounting foot plus Sheet metal screw trapezoidal sheet metal Front adapter, flat Rear adapter, high Search terms: mounting set trapezoidal sheet metal trapezoid

Read more less

Description: A mounting set consists of small feet and larger feet. Ideal for mounting on a flat roof, or on the facade, your module is aligned at an angle of inclination of 10°. The “Standing Feet” mounting set is particularly suitable for users for whom aesthetics and simplicity on the roof or on the wall are very important. Due to the low height of the feet, your solar plant can hardly be seen on a carport, for example. Click here for the assembly video Assembly: Two small feet and two larger feet are required to attach a module. For example, to attach two modules in a row, three small and three larger feet are required. Additional required fastening material in the form of washer head screws, module end clamps and middle clamps are part of the offer. To ensure safe installation, the assembly must be weighed down or firmly anchored. The feet can be ideally connected to concrete curbs or directly to the rafters of the roof. Further information can be found in the assembly instructions Material: aluminum Color: silver Dimensions: Mounting foot 1: width 70 mm / height: 220 mm, Mounting foot 2: Width: 70 mm / Height: 60 mm Module relocation: across a floor or wall

Read more less

Description: The mounting plate connects profile rails to the support triangle flat roof system. Four mounting plates are required for each support triangle. The grooved back connects firmly to the nut and locks the screw in the profile rail channel. Scope of delivery: Mounting plate M10 hammer head screw M10 nut with locking teeth

Read more less

Solar profile strip - mounting rail 40x40mm Mounting rails are mainly used for roof mounting, wall mounting and balcony mounting. In order to guarantee the weather resistance of your system, we strongly recommend secure installation with a rail or a professional fastening system. The advantages of rail are obvious Easy to handle and align (level) Variable in orientation (horizontal, vertical) Safety of installation (slot nuts, clamps, etc. are firmly anchored in the mounting channel) Clearly defined channels 1.) for module fastening and 2.) for mounting fastening (roof hooks, elevations, balcony holders, etc.) prevent confusion or incorrect installation Please order the fastening material required for module assembly such as slot nuts, module end clamps, middle clamps and cylinder head screws separately. Please order mounting materials for fastening (balcony fastenings, roof hooks, washer head screws, hanger screws) separately and can be viewed in the shop. 1 module horizontal = 2 x mounting rail 1.1m 1 module vertical = 2 x mounting rail 1.80m If you have any questions about the right mounting material, please feel free to contact us.

Read more less

Elevation balcony power plant flat roof The solar elevation 20° - 40° mounting set consists of solid elevation triangles. The inclination of the modules can be flexibly adjusted between 20° and 40°. In order to always achieve the highest power yield, the tilt angle is adjusted to a flat 20° in summer and to a maximum tilt of 40° in winter. We wish you a good solar harvest. In just a few simple steps you can become a power generator, take a look at our assembly instructions . Find our assembly video here. The set is suitable for modules with a width of up to 115cm Assembly: Two support triangles are required to attach a module. Three support triangles are required to attach two modules in a row. View our assembly instructions here. Additional required mounting material in the form of profile rails, fastening screws, middle and end clamps, and covers are part of the offer. To ensure safe installation, the assembly must be weighed down or firmly anchored. The support triangles can be weighted down with stone slabs or curbs without drilling. Our basic flat roof installation set provides for vertical installation (ie in portrait orientation). If you want to mount your modules horizontally, i.e. across (landscape), you will need longer profile rails. Call us or send us an email with your request and we will send you an offer. Scope of delivery: Assembly triangles Profile rails in 1.20m length Mounting plate End caps End clamps & if necessary middle clamps Additional Information: Balcony power plant on the carport / flat roof Balcony power plant on the flat roof - electricity in 15 minutes Search terms: mounting set for elevation 20 40 flat roof,

Read more less

Description: The hanger screw mounting set is perfect for waterproof installation on sheet metal roofs with a wooden substructure. The hanger bolt has a wood or dowel thread on one side and a metal thread on the other side. The extra-long metal thread offers enough flexibility for height adjustment. Installation is carried out using a standard screwdriver and key attachment. You can find the assembly video here The set is suitable for modules up to a width of 115cm Fastening set of hanger screws for corrugated iron, sheet metal roofs, corrugated panels (1 module) 4 hanger bolts M10, 250mm 4 adapter plates for connecting hanger bolts and profile 2 aluminum profile rails 1.20m 4 cover caps for aluminum profile rails 4 end clamps including screws for module attachment Hanger screw fastening set (2 modules) 6 hanger bolts M10, 250mm 6 adapter plates for connecting hanger bolts and profile 2 aluminum profile rails approx. 2.10m (or 4 x 1.20m with connecting rails) 4 cover caps for aluminum profile rails 4 end clamps including screws for module attachment 2 middle clamps for module attachment A mounting set contains all screws, washers, etc. for attaching one or two modules.

Read more less

Description The trapezoidal sheet metal installation set is ideal for waterproof installation on the raised beads of trapezoidal sheet metal roofs. With the Trapezoidal Sheet Plus mounting set you have the option of mounting your modules both horizontally and vertically. The adapter rails allow you to raise your modules by up to 7 degrees and thus generate electricity more effectively. By clamping on the long side of the frame, the module maintains the best possible load capacity. Thanks to special sheet metal screws, fastening takes place without pre-drilling. Screws and already glued EPDM sealing rings prevent moisture from penetrating. The module is mounted directly on the mounting rails or with additional mounting adapters using module clamps. Click here for the data sheet and assembly instructions Fastening set for trapezoidal sheet metal (1 module) 4 x mounting rails (10cm) including seal 2 x front adapters 2 x rear adapters 4 x end clamps including screws for module attachment 4 x Rhombus Nuts 16 x Sheet Metal Screws Fastening set for trapezoidal sheet metal (2 modules) 6 x mounting rails (10cm) including seal 3 x front adapters 3 x rear adapters 4 x end clamps including screws for module attachment 2 x Middle Clamps 6 x Rhombus Nuts 24 x Sheet Metal Screws Complementary products: Mounting foot plus Sheet metal screw trapezoidal sheet metal Front adapter, flat Rear adapter, high A mounting set contains all screws, washers, etc. for attaching one or two modules. If necessary, slightly different systems are used. Search terms: mounting set trapezoidal sheet metal

Read more less

Description: The triple flexible roof hook system adapts ideally to the conditions of your tiled roof. Regardless of whether there is a single or double batten under the pans, whether the rafters and pans are not evenly distributed or whether the distance between solar modules and roof tiles needs to be flexibly aligned - with a three-way adjustable roof hook you retain full flexibility. Roof hooks made of steel guarantee the dynamic balancing of loads caused by wind, snow and weather for decades. In just a few simple steps you can become a power generator, take a look at our assembly instructions . The set is suitable for modules with a width of up to 115cm Roof hook fastening set for roof tiles, roof tiles (1 module) 4 roof hooks, 3-way adjustable in height and width 2 aluminum profile rails 1.20m 4 cover caps for aluminum profile rails 4 end clamps including screws for module attachment Roof hook fastening set (2 modules) 6 roof hooks , 3-way adjustable in height and width 4 aluminum profile rails 1.20m 4 profile rail connectors 4 cover caps for aluminum profile rails 4 end clamps including screws for module attachment 2 middle clamps for module attachment A mounting set contains all screws, washers, etc. for attaching one or two modules.

Read more less

Heckert NEMO® 4.2 80 M 400 Watt Made in Germany Monocrystalline PV module in silver Description of services: The NeMo® 4.2 80 M solar module perfects the combination of durability and performance. An extremely durable and stable modular structure with 35mm thickness, as well as reliable performance with elegant aesthetics. The mono modules with the 400 watt performance class have an efficiency of 20.5%. Heckert solar modules are manufactured using the latest technology at the Chemnitz location manufactured. Sustainable production uses green electricity from our own PV systems around the site or purchased green electricity. One pallet contains 30 solar modules Performance data: 80 monocrystalline cells Rated power 400 Wp 12 bus bar Dimensions: 1736 x 1122 x 35 mm Plus sorted: up to 4.99 Wp additional power 15 year guarantee The details can be found in the technical data sheet Our Glossary/Lexicon explains the most important technical terms. Do you have further questions about the product/technology or would you like to read more? In our Blog find answers & cool stories!

Read more less

Rhombus nuts / threaded plates / sliding nut M8 For attaching inverters to the mounting profile For fastening end clamps and middle clamps in the mounting profile

Read more less

Schuko plug IP54 made of solid rubber for quick and safe installation - complete protection against contact - Protection against splashing water

Read more less

Description The locking screw plus prevents inserted adapters from slipping out of the trapezoidal sheet metal mounting system. After installing the trapezoidal sheet metal bridges & adapters, the securing set is screwed in at the outer points of your installation. scope of delivery 1 x M8 screw 1 x Washer 1 x Rhombus Nut Complementary products: Mounting foot plus Sheet metal screw trapezoidal sheet metal Front adapter, flat Rear adapter, high Search terms: Mounting set trapezoidal sheet metal trapezoid

Read more less